Close Menu
MobileRdx
    Facebook X (Twitter) Instagram
    MobileRdxMobileRdx
    • Hardware
      • Samsung
      • Xiaomi Hardware
      • Huawei Hardware
      • Oppo Hardware
      • Vivo Hardware
    • Box Setup
      • UnlockTool Setup
      • TFT Unlock Tool
      • UFI Box
      • Easy Jtag Plus Box
      • Infinity CM2
      • Z3x Box Samsung Tool PRO
      • Miracle Box
    • GsmTools
    • Contact Us
    • Privacy Policy
    |
    MobileRdx
    Home » Uncategorized » iPhone 8 Plus Charging Problem Ways – Charging Jumper Solution
    Uncategorized

    iPhone 8 Plus Charging Problem Ways – Charging Jumper Solution

    By Mobile RdxSeptember 20, 2018

    iPhone 8 Plus Charging Problem Ways – Charging Jumper Solution

    iPhone 8 Plus Charging Solution Charging Ways Not Charging Problem USB Ways Fake Charging Problem Charging IC Solution

    Here is the solution for iPhone 8 Plus Not Charging problem like there is No Charging indication shows on the display when the battery charger is being a plug-in.
    This problem is may cause by faulty components iPhone 8 Plus PCB board. This problem may sometimes happen if the device suffered wet or water damaged or just exist

    For those that own a iPhone 8 Plus, you may be having a problem that the iPhone 8 Plus not charging correctly. iPhone 8 Plus owners thought that the USB cable was an issue for the Samsung not charging. So they went out and purchased a new charger, instead, some quick methods that we’re about to suggest can generally fix the problem when the iPhone 8 Plus not charging when plugged in.

    Problems

    • Phone not Charging.
    • Showing “Charger Not Connected” error message.
    • Phone heats up during charging.

    Manual Solution

    • Check with any other original Nokia Lumia charger.
    • Clean Charging connectors and check

    Hardware Solution:

    iPhone 8 Plus Charging Problem Ways Charging Jumper Solution

    Check Charging connector for any kind of water damage, if it is then clean it and check.

    Now re-solder charging connector pins and check.
    Check charging voltage with the help of a multimeter. Place Negative terminal of the multimeter on ground and Positive on a charging pin (1st pin from your left-hand side).
    Make sure that the voltage is between 5V to 5.5V, if it is not then replaced charging connector. (Charging Connector can be replaced by heating it from the opposite side of the board, while heating it, pull charging connector with the help of Tweezers).
    Now remove metal sheet covering the charging section (It contains Charging IC and Components).
    Check continuity between Fuse and Charging Pin (1st from your left-hand side). If there is no continuity, place jumper.
    Also, check the following, and replace them if damaged:
    Fuse
    Capacitor
    Coil
    Heat charging IC, if it is faulty then replace it.
    Now check charge at the battery terminals, if it is not standard voltage then re-solder or replace battery terminals.

    Read More:-  Blackberry 9700 Keypad Not Working Problem Full Solution

    Related Posts

    Realme C55 RMX3710 ISP Pinout

    Realme C55 ISP PinOUT EMMC Ways | Test Point

    Xiaomi Redmi A5 EMMC ISP PinOUT

    Xiaomi Redmi A5 EMMC ISP PinOUT | Test Point

    Realme 12 5G RMX3999 UFS ISP PinOUT

    Realme 12 5G UFS ISP PinOUT | Test Point

    Add A Comment
    Leave A Reply Cancel Reply

    All Box Latest Setup
    UnlockTool V2025.07.14.0
    TFT Unlock Tool v6.2.1.1 – Free
    Miracle BFT Best Flash Tool V1.7
    UMT Tool Setup QCFire (v12.01)
    Z3x SamsTool Online V1.10
    Infinity CM2 Latest Setup
    Android Utility Pro V186.00.8016
    EFT Dongle V5.0.2 Setup
    Z3x Box Samsung Setup V45.14
    Hydra Tool Setup V6.0

    Facebook X (Twitter) Instagram Pinterest
    • About Us
    • Contact Us
    • Privacy Policy
    © 2025 MobileRdx. Made with ❤️ in India

    Type above and press Enter to search. Press Esc to cancel.