Close Menu
MobileRdx
    Facebook X (Twitter) Instagram
    MobileRdxMobileRdx
    • Hardware
      • Samsung
      • Xiaomi Hardware
      • Huawei Hardware
      • Oppo Hardware
      • Vivo Hardware
    • Box Setup
      • UnlockTool Setup
      • Flash64 Box Setup
      • TFT Unlock Tool
      • Z3x SamsTool Online Tool
      • UFI Box
      • Easy Jtag Plus Box
      • Infinity CM2
    • GsmTools
    • Contact Us
    • Privacy Policy
    |
    MobileRdx
    |

    Realme 13 5G UFS ISP Pinout (Tested)

    By Mobile RdxNovember 20, 2026 Uncategorized
    Realme 13 5G UFS ISP Pinout (Tested)

    If you are searching for the working Realme 13 5G UFS ISP pinout, you are at the right place. The Realme 13 5G runs on the MediaTek Dimensity 6300 platform with UFS storage. In this post, we have shared the tested ISP pinout points that work for restore the stock ROM, bypass FRP lock, remove MDM Lock, repair a Dead Boot, or clear user data directly through Flash64, UFI Box, or Easy JTAG.

    In this post, you will find the Realme 13 5G ISP Pinout diagram, device information, UFS connection details, and important precautions for performing ISP operations.

    What is ISP pinout?

    ISP in system programming allows us to access the eMMC/UFS memory directly with the device still soldered to the PCB (printed circuit board) using a proper box/dongle, such as Flash64 UFI, Easy-JTAG, or Medusa.

    Using correct ISP connections technicians can connect a device to a supported UFS programmer for storage detection, reading and writing as well as for troubleshooting operations.

    Realme 13 5G ISP Pinout Image:

    Carefully remove the back cover of Realme 13 5G by applying controlled heat to soften the adhesive. The ISP Pinout enables you to carefully boot into Flash Mode. So, follow the methods below to successfully boot to ISP mode.

    Pinout Labels:

    RXOP – Receive Out Positive

    RXON – Receive Out Negative

    TXOP – Transmit Out Positive

    TXON – Transmit Out Negative

    Realme 13 5G UFS ISP Pinout

    Tip: You can use a microscope or a 10x magnifier to identify the points correctly.

    Required Tools for ISP Pinout:

    • Make sure your table is set up with the right tools before jumping in:
    • UFI Box, Flash64, or EasyJtag
    • 0.1mm – 0.3mm jumper wire
    • Fine tip soldering iron
    • Isopropyl Cleaner (IPA 99%)
    • Soldering flux
    • Multimeter (for checking continuity)
    Read More:-  Samsung GT-S7362 Network Problem Solution Jumper Ways

    How to Connect Realme 13 5G ISP to the UFS Box

    • Remove the battery first—prevents voltage conflicts.
    • Clean the board area with isopropyl alcohol.
    • Solder jumper wires to CLK, TXOP, TXON, RXOP and RXON points.
    • Connect the wires to your UFS/EMMC tool following its pinout.
    • Check every wire with a multimeter for shorts.
    • Connect ISP to UFI or Easy JTAG,
    • In the UFI or Easy JTAG software:
    • Click Identify UFS
    Connect Realme 13 5G ISP to the UFI Box
    • FRP Bypass: Go to: User Partition – Special Task – Reset FRP
    • Fix Dead Boot: Select the firmware & click flash.
    • Done.

    If the connection is right, you will see the UFS chip info appear in the tool window.

    Related Posts

    Realme 12 Pro 5G RMX3842 UFS ISP Pinout (Without CPU Drill)

    Vivo Y21 5G PD2542 ISP Pinout [Tested]

    Samsung Z Fold5 UFS ISP Pinout

    Add A Comment
    Leave A Reply Cancel Reply

    All Box Latest Setup
    UnlockTool V2026.11.17.0
    BFT Best Flash Tool V1.7 – Free
    MRT Tool V6.1.0 – Free
    TFT Unlock Tool v6.2.1.1 – Free
    UMT Tool Setup QCFire (v14.4)
    EFT Dongle V5.6.8 Setup
    Easy JTAG Plus Box Setup
    Android Utility Pro V202.00.1225
    Z3x SamsTool Online V1.41
    Facebook Telegram Pinterest Instagram
    • About Us
    • Contact Us
    • Privacy Policy
    © 2026 MobileRdx. Made with โค๏ธ in India

    Type above and press Enter to search. Press Esc to cancel.