In this guide, we’ll share a clear working image of the Samsung A57 SM-A576B UFS ISP pinout that you may be able to use to flash firmware/ROM dump, remove FRP lock, unlock MDM locks from Samsung A57 5G, fix dead boot issues, or reprogram the UFS chip using one of the many ISP-compatible boxes such as UFi Box, Easy JTAG, and Flash64 Box. We will also provide details on connecting the ISP pinout to a proper UFS programmer box.
As the Samsung A57 SM-A576B series (launched in early 2026) uses high-speed UFS (Universal Flash Storage) instead of the older eMMC, the connection method and pinout logic have been modified. This guide provides the technical breakdown for ISP connections on this specific hardware.
What is an ISP pinout?
ISP is short for In-System Programming. This means you can communicate directly with your memory chip (e.g., eMMC or UFS) while still in the system (i.e., without removing the chip from the circuit board…or Chip Off). Using special soldered jumper wires attached to either test points or resistors on the logic board, you can bypass the bad CPU, then read the information right out of the memory chip using one of these programmer boxes, such as a Flash64, Easy JTAG Plus, Medusa Pro II, or UFI Box.
Samsung A57 SM-A576B UFS ISP Pinout Image:
The test points are located on the main motherboard, near the UFS memory chip area, as shown in the inset image. To access to the points, you might have to scratch away the protective mask or remove a small section of the EMI shielding.
Key Pinout Points for UFS:
- REF_CLK: Reference clock signal.
- RST: Hardware Reset line.
- TX0_P / TX0_N: Transmit differential pair (Positive/Negative).
- RX0_P / RX0_N: Receive differential pair (Positive/Negative).
- VCC: Core voltage (usually 2.5V or 3.3V).
- VCCQ2: I/O voltage (usually 1.8V).
Required Tools for ISP Pinout:
Make sure your bench is set up with the right tools before making jumpers.
- Flash64 Box UFI Box, or Easy JTAG
- 0.1mm – 0.3mm jumper wire
- Fine tip soldering iron
- Isopropyl Cleaner (IPA 99%)
- Soldering flux
- Multimeter (for checking continuity)
How to Connect Samsung A57 SM-A576B ISP to the UFS Box
- Remove the battery from the phone—this is extremely important to prevent voltage conflicts.
- Clean the PC board area with isopropyl alcohol.
- Connect jumper wires to Rst, Txop, Txon, Rxop, and Rxon points with care using solder.
- Connect the wires to your UFS/EMMC tool according to the tool’s pinout.
- Double-check each wire using a multimeter to ensure there are no shorts.
- Connect to UFI or Easy JTAG,
- In the UFI or Easy JTAG software:
- Select Identify UFS eMMC
- Now Use the Operation You Want: User Partition – Special Task – Reset FRP
If you have the right connection, you will see the UFS chip information in the tool window.
Frequently Asked Questions
The Samsung A57 ISP pinout allows technicians to connect directly to the phone’s UFS memory chip without removing it from the motherboard (no chip-off required).
You need a professional UFS programmer box and accurate soldering tools:
Boxes: Easy JTAG Plus, UFI Box, Medusa Pro, or Flash64.
Tools: 0.1 mm jumper wire, a fine-tip soldering iron, and a multimeter.
Re-check your soldering for loose wires.
Check the wires are as short as possible to prevent data loss.
Verify that you have correctly connected the GND (Ground).
Yes—always disconnect the battery before soldering or connecting to a UFS box.
Professional mobile technicians
Experienced hardware repair engineers
Technicians with proper UFS tools
